View and Download Chauvet Intimidator Spot LED 350 user manual online. Intimidator Spot LED 350 DJ Equipment pdf manual download. 2k5 bob long intimidator manual maytexde, download and read 2k5 bob long. Virtue board bob long 2k5 alias intimidator ebay, find best value and selection for.

If your Spire continues to slowly spin after it’s loaded, check the following: • Are you using fresh brand name batteries? Duracell or Energizers are best (lithium ion not necessary). Low batteries and/or non-brand name batteries may not output enough voltage to allow the motor to detect when it should stop. • Inspect Spire drive fingers. Check to make sure the Spire drive fingers are in good condition. If damaged, • Turn the Yellow “Drive Pressure” setting to 1 by following these steps.

• Hold in the LED cover/force feed button and turn the Spire on. • When the Spire turns on, release the LED button and ten release the power button. • Tap the LED button until the light changes to yellow for the Drive Pressure setting. • Hold in the LED button until it blinks (release when it starts blinking).

Count the number of blinks – that is what it is currently set to. • Tap the LED button one time to set the value to 1. If you wait too long to enter your setting, you will need to hold the LED button in again until it blinks.

• Turn off the Spire, fill with paint, and check to see if spinning has stopped. • If these options do not work, directly and we will help you to fix the problem. If your Spire continues to spin extremely fast after its loaded, the G-force sensor is likely falsely detecting shots and telling the Spire to spin. Try the following solutions to solve the problem: • Make sure the Tray is properly installed and seated securely into the loader. Make sure the loader is securely attached to the marker (with barrel cover installed). • Check that the Red Sensitivity setting is set to the default 4 or lower. • Hold in the LED cover/force feed button and turn the Spire on.

• When the Spire turns on, release the LED button and ten release the power button. • Tap the LED button until the light changes to red for the G-force Sensitivity setting. • Hold in the LED button until it blinks (release when it starts blinking). Count the number of blinks – that is what it is currently set to and turn to 4 if it’s set to 5, or turn to 3 if it’s set to 4.

• Tap the LED button 3 (or 4 depending on where you want to set it) times to set the value to 1. If you wait too long to enter your setting, you will need to hold the LED button in again until it blinks. • Turn off the Spire, fill with paint, and press the LED button to initiate an auto-force feed and check to see if spinning has stopped after it makes an initial spin. • Check Tray Retainer. Remove Spire Tray from shells and look inside the nose of the shells.

Make sure the Black Tray Retainer is installed and not damaged in the front of the shells. If it is missing or damaged, • Reposition G-force sensor & check sensor foam. Remove Spire Tray, check that the black rectangular G-force sensor in the front of the tray has foam on both sides.

Slightly tug the sensor downwards (the wires running under the battery pack hold it in place so it will only move 1/4″ at most). Then re-seat the sensor back into its original location. Check the Spire with paint to see if the problem is solved. • If these options do not work, directly and we will help you to fix the problem. The Spire is designed to feed as fast as necessary for today’s style of game play in all the major leagues around the world.

This includes 15bps ramping, 12.5 bps ramping, and 10.5bs ramping. With a shot activated G-force sensor, the Spire is also designed to feed fast as the gun is shooting. Bob Long Technologies reported peak BPS speeds on 32bps using his markers on uncapped settings. If your Spire is not feeding fast enough, or skipping shots and you are certain it’s not due to gun settings, check the following: • • Are you using fresh brand name batteries?

Duracell or Energizers are best (lithium ion not necessary). Low batteries and/or non-brand name batteries will not output enough voltage to allow the motor to perform well. • Inspect Spire drive fingers.